{"product_id":"eversolo-amp-f2-stereo-power-amplifier","title":"EverSolo AMP-F2 Stereo Power Amplifier","description":"\u003ch2\u003eWhat You Need to Know\u003c\/h2\u003e\n\u003ch3\u003eWhat Is the EverSolo AMP-F2 — and What Does It Do?\u003c\/h3\u003e\n\u003cp\u003eA power amp does one thing: it takes the signal from your preamp or streamer and turns it into the power that drives your speakers. It doesn’t stream music. It has no DAC and no volume control. It’s the muscle of your system.\u003c\/p\u003e\n\u003cp\u003eThe AMP-F2 was built to be that muscle at a price that was once out of reach. EverSolo teamed up with \u003cstrong\u003eStarke Sound\u003c\/strong\u003e— an amp company based in California — to build this unit around Starke’s custom \u003cstrong\u003eNS600 module\u003c\/strong\u003e. The result is a compact, 8-pound amp with serious output.\u003c\/p\u003e\n\u003cp\u003eIn stereo mode it puts out \u003cstrong\u003e145 watts per channel at 8 ohms\u003c\/strong\u003e and \u003cstrong\u003e250 watts per channel at 4 ohms\u003c\/strong\u003e. In bridged mono mode it reaches \u003cstrong\u003e450 watts at 2 ohms\u003c\/strong\u003e. That’s enough power for almost any speaker made.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e The AMP-F2 is a power amp only. You need a separate preamp or streamer to control volume and pick your source. It pairs well with EverSolo’s DMP-A6 or DMP-A8, but works with any preamp that has XLR or RCA outputs.\u003c\/p\u003e\n\u003ch3\u003eWhat Makes This Amp Different?\u003c\/h3\u003e\n\u003cp\u003eMost amps at $799 use generic circuits. The AMP-F2 uses a module built by Starke Sound just for hi-fi use. The NS600 module runs \u003cstrong\u003ePurePath Ultra-HD technology\u003c\/strong\u003e with fast error-correction feedback. This keeps distortion very low across all frequencies.\u003c\/p\u003e\n\u003cp\u003eThe amp switches internally at up to \u003cstrong\u003e600kHz\u003c\/strong\u003e — far above what you can hear. A faster switching rate means the amp tracks the music signal more closely. The \u003cstrong\u003eSAPS power supply\u003c\/strong\u003e feeds the circuit a clean, stable signal with very low noise.\u003c\/p\u003e\n\u003cp\u003eSignal-to-noise ratio tops 110dB. Total distortion is 0.003% at 10 watts. Those are numbers you’d expect from amps that cost much more.\u003c\/p\u003e\n\u003ch3\u003eBridged Mono: What It Means and When to Use It\u003c\/h3\u003e\n\u003cp\u003eThe AMP-F2 is \u003cstrong\u003ebridgeable\u003c\/strong\u003e. Flip a switch on the back and both channels combine into one powerful mono channel — up to 450W at 2 ohms. In that mode, the amp drives a single speaker. You’d use one AMP-F2 per channel of your system.\u003c\/p\u003e\n\u003cp\u003eMost people won’t need this. Standard stereo mode is plenty for most setups. But if your speakers are very hard to drive, or you want to run two AMP-F2 units as mono blocks, bridging gives you the extra power.\u003c\/p\u003e\n\u003ch3\u003eWho Is This Product Best For?\u003c\/h3\u003e\n\u003cp\u003e✔️ You already own a preamp or streamer with XLR or RCA outputs and want a strong power amp to finish your system.\u003c\/p\u003e\n\u003cp\u003e✔️ You use an EverSolo DMP-A6 or DMP-A8 and want a power amp built to work right alongside it.\u003c\/p\u003e\n\u003cp\u003e✔️ You have speakers that need real power — large bookshelf or floor-standing models — and want an amp with room to spare.\u003c\/p\u003e\n\u003cp\u003e✔️ You want to run two AMP-F2 units as mono blocks — one per channel, each bridged — for maximum power and channel separation.\u003c\/p\u003e\n\u003cp\u003e✔️ You care about energy use — the AMP-F2 draws only 14 watts at idle and less than 0.5 watts in standby.\u003c\/p\u003e\n\u003cp\u003eOne honest note: some users have reported a faint background hiss with very sensitive speakers — especially in near-field setups. If you use highly sensitive speakers (98dB+ sensitivity) at close range, it’s worth checking with us before you buy.\u003c\/p\u003e\n\u003ch3\u003eHow Does It Connect to Your System?\u003c\/h3\u003e\n\u003cp\u003eThe back panel has two sets of inputs: a pair of \u003cstrong\u003eXLR balanced inputs\u003c\/strong\u003e and a pair of \u003cstrong\u003eRCA single-ended inputs\u003c\/strong\u003e. Use the XLR inputs if your preamp or streamer supports balanced connections — balanced wiring is quieter and is generally preferred for longer cable runs. The RCA inputs work with any standard preamp output.\u003c\/p\u003e\n\u003cp\u003eSpeaker connections use two pairs of \u003cstrong\u003ecustom beryllium copper binding posts\u003c\/strong\u003e made by Starke Sound. Beryllium copper is used for its excellent conductivity and durability. You can connect one or two pairs of speaker cables per channel if your speakers support bi-wiring.\u003c\/p\u003e\n\u003cp\u003eThe AMP-F2 has both \u003cstrong\u003e12V Trigger In and Trigger Out\u003c\/strong\u003e jacks. This lets it power on and off automatically when your preamp or streamer does. A USB-to-Trigger adapter cable is included in the box — plug it into the USB port on an EverSolo DMP-A6 and the AMP-F2 will sync its power state automatically.\u003c\/p\u003e\n\u003cp\u003eThe bridging switch is on the rear panel. Flip it to mono and use only the left-channel inputs and one pair of binding posts. In bridged mode, the amp delivers up to 450W at 2 ohms and handles loads as low as 0.8 ohms.\u003c\/p\u003e\n\u003ch2\u003eWhat’s in the Box\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eEverSolo AMP-F2 Stereo Power Amplifier\u003c\/li\u003e\n\u003cli\u003eAC Power Cord\u003c\/li\u003e\n\u003cli\u003eUSB-to-12V Trigger Adapter Cable (for EverSolo DMP-A6 sync)\u003c\/li\u003e\n\u003cli\u003eManufacturer’s Warranty Card\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eNote: XLR or RCA interconnect cables and speaker cables are not included and must be purchased separately.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch2\u003eWhat Listeners and Reviewers Are Saying\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eEditor’s Choice Award 2025–2026 — \u003cem\u003eavforums.com\u003c\/em\u003e | Ed Selley | November 27, 2025\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSelley gave EverSolo his Best Hi-Fi Brand award for 2025–2026. The AMP-F2 was part of the lineup he cited. His view: EverSolo makes gear that does more, sounds better, and is built to a higher standard than most rivals at the price. The award covers the full EverSolo range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower Amplifier Review — \u003cem\u003eThe Audio Tailor\u003c\/em\u003e | October 2024\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Audio Tailor tested the AMP-F2 with soft music and loud full-band tracks. The amp held its own on both. Their verdict: strong power, clean sound, and great value. They called it a top pick for serious listeners who don’t want to pay more than they have to.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eListener Review — \u003cem\u003eHiFi Guides Forum\u003c\/em\u003e | raptor168 | March 2024\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis listener ran the AMP-F2 with Sonus Faber speakers for a long test. He called it a keeper and said it beat every hope he had for a Class D amp. His final word: it’s the last amp he’ll need to buy. Note: this is a forum post, not a staff review.\u003c\/p\u003e\n\u003ch2\u003eBuilding Your System? Here Are Some Great Companions.\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEverSolo DMP-A6 Streamer\/DAC\/Preamp\u003c\/strong\u003e — The natural partner for the AMP-F2. The DMP-A6 provides streaming, DAC, and preamplifier functions, and its USB port syncs with the AMP-F2’s trigger input for automatic power-on\/off. \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/shop-all\/brands\/eversolo\/\"\u003eBrowse EverSolo streamers\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpeakers\u003c\/strong\u003e — The AMP-F2’s power output (250W\/4Ω stereo; 450W bridged) gives you headroom for both bookshelf and floorstanding speakers. \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/speakers\/bookshelf-speakers\/\"\u003eBrowse bookshelf speakers\u003c\/a\u003e or \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/speakers\/bookshelf-speakers\/\"\u003ebrowse floorstanding speakers\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXLR Balanced Interconnects\u003c\/strong\u003e — If your preamp has XLR outputs, balanced cables give you a quieter signal path. \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/aa-interconnect-xlr\"\u003eBrowse XLR cables\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpeaker Cables\u003c\/strong\u003e — Quality speaker cable makes the most of the AMP-F2’s power delivery. \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/cables\/speaker-cables\/\"\u003eBrowse speaker cables\u003c\/a\u003e — our Pangea Audio cables offer excellent value.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubwoofer\u003c\/strong\u003e — If your preamp has a sub output, adding a subwoofer pairs well with the AMP-F2 for a full-range system. \u003ca href=\"%%GLOBAL_ShopPathSSL%%\/speakers\/subwoofers\/\"\u003eBrowse subwoofers\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures \u0026amp; Specifications\u003c\/h2\u003e\n\u003ch3\u003eCo-Designed with Starke Sound — Built Around the NS600 Module\u003c\/h3\u003e\n\u003cp\u003eStarke Sound is an amp company based in California. They build high-power designs for demanding home audio systems. EverSolo worked with their team to build the AMP-F2 around Starke’s NS600 module. This is not a stock circuit — it was made for hi-fi use.\u003c\/p\u003e\n\u003ch3\u003eClass D with PurePath Ultra-HD Technology\u003c\/h3\u003e\n\u003cp\u003eClass D amps are very efficient. They run cool and use little power at idle. The NS600 module uses Texas Instruments’ PurePath Ultra-HD tech with fast error-correction built in. This holds distortion very low across all frequencies. The AMP-F2 puts out about 65 BTU of heat per hour — less than a light bulb.\u003c\/p\u003e\n\u003ch3\u003eSerious Power — 250W Stereo, 450W Bridged\u003c\/h3\u003e\n\u003cp\u003eStereo mode: 145W per channel at 8 ohms, 250W per channel at 4 ohms. Bridged mono: 280W at 4 ohms, 450W at 2 ohms. Peak current is 16.5 amps per channel, or 33 amps when bridged. The amp can handle loads as low as 0.8 ohms — well below what most speakers ever demand.\u003c\/p\u003e\n\u003ch3\u003eSAPS Audio-Specific Switch Power Supply\u003c\/h3\u003e\n\u003cp\u003eThe SAPS supply was built just for audio use. It holds 600 watts of reserve power with very low ripple and very low electrical noise. A clean power supply means a clean signal to your speakers. This is one of the main things that sets the AMP-F2 apart from cheaper Class D designs.\u003c\/p\u003e\n\u003ch3\u003e600kHz Internal Switching Rate\u003c\/h3\u003e\n\u003cp\u003eThe amp switches internally at up to 600kHz — far above what you can hear. A faster switching rate means the amp tracks the music signal more exactly. It also makes the output filter simpler and more effective. This helps keep the noise floor low and the signal-to-noise ratio high — over 110dB.\u003c\/p\u003e\n\u003ch3\u003eBalanced XLR and Single-Ended RCA Inputs\u003c\/h3\u003e\n\u003cp\u003eThe AMP-F2 has both XLR (balanced) and RCA (single-ended) inputs. Balanced cables cancel out noise picked up along the cable run. This matters most with long cable runs or noisy rooms. XLR input load is 22kΩ. RCA is 11kΩ. Input level is 2.7V.\u003c\/p\u003e\n\u003ch3\u003eCustom Binding Posts — Made by Starke Sound\u003c\/h3\u003e\n\u003cp\u003eThe speaker posts are made from beryllium copper. This metal carries current well and holds up over time. Two pairs are included per channel. If your speakers have two sets of terminals, you can run two sets of cables — one for highs, one for lows. Starke Sound made these posts just for this amp.\u003c\/p\u003e\n\u003ch3\u003e12V Trigger In and Out — Auto Power Sync\u003c\/h3\u003e\n\u003cp\u003eStandard 12V trigger jacks let the AMP-F2 turn on and off in step with your preamp. A USB-to-trigger cable is in the box. Plug it into the USB port on an EverSolo DMP-A6 and both units will power on and off at the same time. No extra cable or setting needed.\u003c\/p\u003e\n\u003ch3\u003eLow Power Use — 0.5W Standby, 14W Idle\u003c\/h3\u003e\n\u003cp\u003eStandby draw is less than 0.5 watts. Idle draw is less than 14 watts. Full-load max is 900 watts. These figures meet the EU’s ErP energy rules. The amp runs cool and quiet. You can leave it in your rack all day without heat or waste being a concern.\u003c\/p\u003e\n\u003ch3\u003eAluminum Chassis with Shielded Design\u003c\/h3\u003e\n\u003cp\u003eThe body is machined aluminum. The shielded design blocks electrical noise from nearby gear. At 10.6” wide, 9.0” deep, and 3.1” tall, it fits on a standard rack shelf. It also matches the look of other EverSolo units if you’re building a full EverSolo system.\u003c\/p\u003e\n\u003ch3\u003eQuick-Reference Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eOutput Power — Stereo Mode\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e8Ω (1% THD)\u003c\/td\u003e\n\u003ctd\u003e145W RMS per channel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4Ω (1% THD)\u003c\/td\u003e\n\u003ctd\u003e250W RMS per channel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eOutput Power — Bridged Mono Mode\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4Ω (1% THD, BTL)\u003c\/td\u003e\n\u003ctd\u003e280W RMS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2Ω (1% THD, BTL)\u003c\/td\u003e\n\u003ctd\u003e450W RMS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003ePerformance\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAmplifier Type\u003c\/td\u003e\n\u003ctd\u003eClass D (Starke Sound NS600 module)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInternal Switching Rate\u003c\/td\u003e\n\u003ctd\u003eUp to 600kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGain\u003c\/td\u003e\n\u003ctd\u003e21.5dB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal-to-Noise Ratio\u003c\/td\u003e\n\u003ctd\u003e\u0026gt;110dB (A-weighted, 4Ω, 250W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTHD\u003c\/td\u003e\n\u003ctd\u003e0.003% at 10W \/ 1kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFrequency Response\u003c\/td\u003e\n\u003ctd\u003e10Hz–20kHz (–1dB)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDamping Factor\u003c\/td\u003e\n\u003ctd\u003e\u0026gt;100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Impedance\u003c\/td\u003e\n\u003ctd\u003e0.136Ω (5Hz–100kHz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum Load Impedance\u003c\/td\u003e\n\u003ctd\u003e0.8Ω\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMax Output Current\u003c\/td\u003e\n\u003ctd\u003e16.5A per channel; 33A (bridged)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eInputs\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBalanced Input\u003c\/td\u003e\n\u003ctd\u003e1× XLR pair (22kΩ impedance)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-Ended Input\u003c\/td\u003e\n\u003ctd\u003e1× RCA pair (11kΩ impedance)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Sensitivity\u003c\/td\u003e\n\u003ctd\u003e2.7V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eOutputs\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSpeaker Terminals\u003c\/td\u003e\n\u003ctd\u003e2 pairs beryllium copper binding posts per channel (custom, Starke Sound)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eControl \u0026amp; Integration\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e12V Trigger\u003c\/td\u003e\n\u003ctd\u003eIn and Out (standard 3.5mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBridged Mono\u003c\/td\u003e\n\u003ctd\u003eYes — rear panel switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003ePower Consumption\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStandby\u003c\/td\u003e\n\u003ctd\u003e≤0.5W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIdle\u003c\/td\u003e\n\u003ctd\u003e≤14W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum\u003c\/td\u003e\n\u003ctd\u003e900W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeat Output\u003c\/td\u003e\n\u003ctd\u003e65 BTU\/hr\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd colspan=\"2\"\u003e\u003cstrong\u003eGeneral\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChassis\u003c\/td\u003e\n\u003ctd\u003eAluminum (anti-interference shielded design)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions (W × D × H)\u003c\/td\u003e\n\u003ctd\u003e270 × 228 × 90mm (10.6” × 9.0” × 3.1” with feet)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e8.0 lbs (3.6 kg)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWarranty\u003c\/td\u003e\n\u003ctd\u003e1 year parts \u0026amp; labor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cdiv class=\"product-faq gsbp-ab3b28d\"\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003chr\u003e\n\u003ch3\u003eDo I need anything else to use the AMP-F2?\u003c\/h3\u003e\n\u003cp\u003eYes. The AMP-F2 is a power amplifier only — it has no volume control, no DAC, and no streaming. You need a separate preamp or streamer\/preamp to control volume and select your source. It pairs naturally with EverSolo’s DMP-A6 or DMP-A8, but works with any preamp that has XLR or RCA outputs. Speakers and speaker cables are also required and not included.\u003c\/p\u003e\n\u003ch3\u003eWhat preamp or streamer pairs best with the AMP-F2?\u003c\/h3\u003e\n\u003cp\u003eEverSolo designed the AMP-F2 to work alongside their DMP-A6 and DMP-A8 streamer\/DAC\/preamps. A USB-to-Trigger cable is included so the two units power on and off together. That said, the AMP-F2 works with any preamp that has XLR or RCA balanced outputs. If you’d like help picking the right pairing, give us a call at 800-942-0220.\u003c\/p\u003e\n\u003ch3\u003eWhat does “bridged mono” mean, and do I need it?\u003c\/h3\u003e\n\u003cp\u003eBridging combines both channels of the amp into a single, more powerful mono channel. In bridged mode the AMP-F2 delivers up to 450W at 2 ohms — enough for almost any speaker. Most listeners won’t need it. It’s most useful for very power-hungry speakers or for building a dual mono-block setup with two AMP-F2 units.\u003c\/p\u003e\n\u003ch3\u003eWhat speakers work with the AMP-F2?\u003c\/h3\u003e\n\u003cp\u003eAlmost any passive speaker. The AMP-F2 can handle loads as low as 0.8 ohms and delivers up to 16.5 amps of output current per channel. This gives it the ability to drive demanding, low-impedance speakers that would challenge less powerful amps. It pairs equally well with efficient bookshelf speakers and hungry floorstanders.\u003c\/p\u003e\n\u003ch3\u003eIs there a remote control or volume control on the amp itself?\u003c\/h3\u003e\n\u003cp\u003eNo. The AMP-F2 is a pure power amplifier with no volume control and no remote. Volume is controlled by your preamp or streamer. Power on\/off can be automated via the 12V trigger connection — when your preamp or EverSolo streamer powers on, the AMP-F2 follows automatically.\u003c\/p\u003e\n\u003ch3\u003eDoes the AMP-F2 run hot?\u003c\/h3\u003e\n\u003cp\u003eNo. Class D amplifiers are very efficient. The AMP-F2’s heat output is rated at 65 BTU per hour — about the same as a light bulb. It draws only 14 watts at idle. You can safely place it in a closed or semi-enclosed rack without worrying about heat buildup.\u003c\/p\u003e\n\u003ch3\u003eHow does the AMP-F2 differ from the EverSolo AMP-F10?\u003c\/h3\u003e\n\u003cp\u003eThe AMP-F10 is EverSolo’s higher-powered Class AB amplifier. Class AB designs use a traditional analog output stage with a large transformer and large capacitors — the AMP-F10 weighs significantly more and runs warmer. The AMP-F2 uses a more modern Class D design. Both are capable amplifiers, but at different price points and with different sonic characters. Call us if you’d like help deciding.\u003c\/p\u003e\n\u003ch3\u003eWill the AMP-F2 work with my existing non-EverSolo preamp?\u003c\/h3\u003e\n\u003cp\u003eYes. The AMP-F2 has standard XLR and RCA inputs and works with any preamp that has those outputs. You won’t get the automatic USB trigger sync you’d have with an EverSolo DMP-A6, but you can still use the 12V trigger input if your preamp supports it. Otherwise, simply switch it on manually.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ch2\u003eSee It in Action\u003c\/h2\u003e\n\u003ch3\u003eEverSolo AMP-F2 Review — Andrew Robinson\u003c\/h3\u003e\n\u003cp\u003eAndrew Robinson’s full video review of the EverSolo AMP-F2, covering build quality, connectivity, and listening impressions (2024).\u003c\/p\u003e\n\u003cp\u003e\u003ciframe title=\"YouTube video player\" src=\"https:\/\/www.youtube.com\/embed\/xAEsCV-CX6o?si=v4wZkEMVgVTC7yso\" width=\"560\" height=\"315\"\u003e\u003c\/iframe\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cdiv class=\"ec-titlebox-text\"\u003e\n\u003cp\u003e\u003cimg class=\"emoji\" role=\"img\" draggable=\"false\" src=\"https:\/\/s.w.org\/images\/core\/emoji\/17.0.2\/svg\/1f3b5.svg\" alt=\"music note emoji\" width=\"20\"\u003e  \u003cstrong\u003e40+ Years of Expertise\u003c\/strong\u003e — Since 1981, we’ve helped over a million music lovers find the right gear.\u003c\/p\u003e\n\u003cp\u003e\u003cimg class=\"emoji\" role=\"img\" draggable=\"false\" src=\"https:\/\/s.w.org\/images\/core\/emoji\/17.0.2\/svg\/1f504.svg\" alt=\"repeat emoji\" width=\"20\"\u003e  \u003cstrong\u003e60-Day Money-Back Guarantee\u003c\/strong\u003e — Take your time. Listen, enjoy, and make sure it’s right for you.\u003c\/p\u003e\n\u003cp\u003e\u003cimg class=\"emoji\" role=\"img\" draggable=\"false\" src=\"https:\/\/s.w.org\/images\/core\/emoji\/17.0.2\/svg\/1f4de.svg\" alt=\"phone emoji\" width=\"20\"\u003e  \u003cstrong\u003eReal Experts, Real Help\u003c\/strong\u003e — Our team is here at \u003ca href=\"tel:8009420220\"\u003e800-942-0220\u003c\/a\u003e, weekdays 9am–6pm EST.\u003c\/p\u003e\n\u003cp\u003e\u003cimg class=\"emoji\" role=\"img\" draggable=\"false\" src=\"https:\/\/s.w.org\/images\/core\/emoji\/17.0.2\/svg\/1f69a.svg\" alt=\"truck emoji\" width=\"20\"\u003e  \u003cstrong\u003eFree Shipping\u003c\/strong\u003e — On orders over $49.\u003c\/p\u003e\n\u003cp\u003e\u003cimg class=\"emoji\" role=\"img\" draggable=\"false\" src=\"https:\/\/s.w.org\/images\/core\/emoji\/17.0.2\/svg\/1f4b3.svg\" alt=\"credit card emoji\" width=\"20\"\u003e  \u003cstrong\u003eFlexible Payment Options\u003c\/strong\u003e — Financing available.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cp\u003eWant to learn more about power amplifiers and how to build a two-channel hi-fi system? Visit our \u003ca href=\"https:\/\/learningcenter.audioadvisor.com\/\"\u003eAudio Advisor Learning Center\u003c\/a\u003e for guides, tips, and expert advice.\u003c\/p\u003e","brand":"EverSolo","offers":[{"title":"New","offer_id":45983107383469,"sku":"NEW-EVAMPF2","price":799.0,"currency_code":"USD","in_stock":true},{"title":"Demo","offer_id":45983107416237,"sku":"DEMO-EVAMPF2","price":649.37,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0750\/3708\/1773\/files\/EVAMPF2_03_2024__61778.1719433737.1280.1280.jpg?v=1778153982","url":"https:\/\/www.audioadvisor.com\/products\/eversolo-amp-f2-stereo-power-amplifier","provider":"Audio Advisor","version":"1.0","type":"link"}