AudioQuest Evergreen Interconnect Cable - 8.0 Meter - RCA to RCA

Evergreen Is AudioQuest's Best-Known Budget Interconnect

AudioQuest's Evergreen sits one step above Tower in the Bridges & Falls series. It carries both channels in one jacket, uses solid Long-Grain Copper, and ends in AudioQuest's cold-welded gold plugs. It has sat in Stereophile's Recommended Components for years.

Other length & termination options are available. Call us to discuss your needs.

Solid Long-Grain Copper in Foamed Insulation

The wires are solid Long-Grain Copper, or LGC. Solid wire has no strands to rub against one another, which AudioQuest names as a major source of distortion. LGC also has fewer oxides and grain boundaries than ordinary copper. Each wire sits in foamed plastic that is mostly air.

The Cold-Welded, Gold-Plated Plug, Explained

Evergreen ends in AudioQuest's own gold-plated RCA plug. It is cold welded, not soldered. A press bonds the plug to the wire under high pressure. AudioQuest calls solder "a common source of distortion." The cold weld keeps the wire's character right up to the contact.

For noise control, Evergreen uses AudioQuest's Metal-Layer Noise-Dissipation, which absorbs radio-frequency noise before it reaches the ground layer, and all its internal conductors are Direction-Controlled to reduce RF noise. The layout gives the ground path a lower impedance than the signal path for a richer sound. The jacket is a Green/Black Braid.

What Reviewers Are Saying

Evergreen appears in Stereophile's Recommended Components. Stephen Mejias ran it from a laptop to desktop speakers and wrote: "Suddenly, I had real high-fidelity sound coming from my laptop."

What Hi-Fi? reviewed Evergreen on August 1, 2012 and was "immediately surprised by the amount of information this interconnect conveys." It also found the sound lean, warning that the clarity "can veer into brittleness at times."

Who Is This Interconnect Best For?

• You want the classic budget upgrade — Evergreen has sat in Stereophile's list for years, so the choice is safe
• Detail matters more than warmth — What Hi-Fi? heard up-front, expressive vocals, so voices step forward
• Space behind the rack is tight — one slim cable carries both channels, so it bends where a pair will not
• You want no solder in the path — AudioQuest cold welds the plug to the wire, so the joint is metal on metal
• Your left and right jacks sit far apart — both channels share one cable, with a single conductor body that splits at each end into the left and right RCA plugs. If your gear is spread very wide apart, call us

How Does It Connect to Your System?

Run Evergreen from a line-level output, a DAC, streamer, CD player or phono stage, to a line-level input on your amplifier or preamp. Keep left to left and right to right. Push each plug straight on until it seats. Pull it off by the barrel, never by the cable.

Then listen.

Measure the Path, Then Add a Little Slack

Measure the route the cable will really take between your components, around shelves and behind the rack. Then add a little slack. As audio legend George Cardas puts it, "A cable that's just long enough usually turns out to be just not long enough."

A Long Run Between Components?

If your amplifier and speakers sit far from your source, we recommend a long interconnect over a long speaker cable. A really long interconnect affects system performance less than a really long speaker cable.

When Is It Time to Upgrade?

An interconnect often stays in a system for years, so it is easy to overlook. Look again when something else changes: a new DAC, streamer or phono stage, or a better amplifier.

Pairs Well With

An interconnect is one link in the chain. It usually joins these categories.

• Integrated Amplifiers — the usual input end
• Digital-to-Analog Converters — DAC output to amplifier
• Music Streamers — streamer output to amplifier
• Speaker Cables — the last link to the speakers

Frequently Asked Questions

What is the cold-welded, gold-plated plug?

AudioQuest's own gold-plated RCA plug. It is joined to the wire by pressure, not solder. AudioQuest names solder as a common source of distortion.

Is this one cable or two?

One cable. AudioQuest's Bridges & Falls cables carry both channels in a single conductor body that splits at each end into the left and right RCA plugs. There are two plugs at each end and one lead to route behind the rack. It is not sold as a single-RCA cable.

How does Evergreen control noise?

With AudioQuest's Direction-Controlled Conductors. AudioQuest controls the directional grain structure of the wire so induced noise drains away from the circuits it would otherwise disturb.

What warranty does AudioQuest give?

Limited lifetime warranty with proof of purchase from an authorized dealer.

Is there a step up?

AudioQuest Golden Gate is the next rung. It moves from Long-Grain Copper to AudioQuest's smoother Perfect-Surface Copper.

Need a Different Length or Connector?

The most popular configurations are shown on this page. If your system requires a different length or termination, call our audio experts. We'll help you choose the right configuration and arrange a custom cable for your system.

Why Audio Advisor?

• 40+ Years of Expertise — Since 1981, we've helped over a million music lovers find the right gear.
• 60-Day Money-Back Guarantee — Take your time. Listen, enjoy, and make sure it's right for you.
• Real Experts, Real Help — Our team is here to answer your questions at 800-942-0220, weekdays 9am–6pm EST.
• Free Shipping — On orders over $49, delivered to your door.
• Flexible Payment Options — Financing available so you can start listening now.

Learn More

Want to learn more about interconnects or solid-core cables? Visit our Learning Center for guides, tips, and expert advice.