AudioQuest Angel Interconnect Cable - 2.0 Meter - 3.5mm Female to 3.5mm

AudioQuest Angel Tops the Range with Solid Silver Conductors

A 3.5mm mini interconnect carries an analog signal between two components using the same small plug most headphones use, so no adapter is needed on gear already built around that jack.

AudioQuest's Angel is a 3.5mm mini interconnect with solid Perfect-Surface Silver (PSS) conductors, FEP Air-Tubes insulation and Carbon-Based Noise-Dissipation plus a 72v Dielectric-Bias System. It ends in cold-welded, direct-silver-plated red copper plugs and has a Silver on Black nylon-braid jacket. AudioQuest also builds it as a Male-to-Female extension, with a female 3.5mm jack on one end, to the same construction.

Other length & termination options are available. Call us to discuss your needs.

What the Conductors Do

AudioQuest calls Perfect-Surface Silver its highest-quality metal, saying it minimizes the distortion that grain boundaries cause. Solid conductors also prevent strand interaction, a major source of distortion.

Insulation and Noise Control

AudioQuest says its FEP Air-Tubes insulation preserves dynamic contrasts.

Noise control is AudioQuest's Carbon-Based Noise-Dissipation, built from layers of metal and carbon-loaded synthetics, plus the 72v Dielectric-Bias System, which AudioQuest says saturates and polarizes the insulation for clear, dynamic sound against a quiet background.

All internal conductors are Direction-Controlled to reduce RF noise. The Asymmetrical Double-Balanced Geometry is built for single-ended use. AudioQuest says it gives the ground a relatively lower impedance for a richer, more dynamic sound.

The Cold-Welded Plug, Explained

Each plug is joined to the wire by a high-pressure cold weld instead of solder, which AudioQuest calls a common source of distortion. The ground shells are stamped instead of machined, so the metal can be chosen for low distortion. The plug is direct-silver plated, with no underlying layer of nickel, which AudioQuest says can cause distortion.

Who Is This Interconnect Best For?

• Your 3.5mm cable does not quite reach — this Male-to-Female extension adds reach to a 3.5mm cable you already own, with the same construction as the standard cable
• You are extending a portable source to a desktop amplifier — a phone, player or compact DAC feeding an amplifier is the short, single-ended run this cable is built for
• You want no solder in the path — AudioQuest cold welds each plug to the wire, so the joint is metal on metal
• You already own AudioQuest Yosemite — Angel is a step up from Yosemite in AudioQuest's 3.5mm mini range
• Your gear uses RCA jacks instead of 3.5mm — check your amplifier's actual input type before ordering; this cable only fits a 3.5mm jack at both ends

How Does It Connect to Your System?

Plug one 3.5mm end into your source's headphone or line-out jack, and the other end into the matching 3.5mm input on your amplifier or receiver. For the Male-to-Female extension, plug the male end of your existing 3.5mm cable into the female jack, and the extension's male end into your amplifier or receiver.

Then power up the system as usual.

Measure the Path, Then Add a Little Slack

Measure the route the cable will really take from your source to your amplifier or receiver, around furniture and behind the rack. Then add a little slack. As audio legend George Cardas puts it, "A cable that's just long enough usually turns out to be just not long enough."

When Is It Time to Upgrade?

An interconnect often stays in a system for years, so it is easy to overlook. Look again when something else changes: a new DAC, streamer or headphone amplifier, or a better amplifier.

Pairs Well With

A 3.5mm interconnect is one link between a source and an amplifier or receiver. It usually joins these categories.

• Music Streamers — many portable and desktop streamers use a 3.5mm output
• Headphone Amplifiers — a common source for a 3.5mm line-level feed
• Digital-to-Analog Converters — some compact DACs use a 3.5mm output instead of RCA
• Integrated Amplifiers — the usual destination for the far end of this cable

Frequently Asked Questions

What is the difference between the Male-to-Male and Male-to-Female versions?

AudioQuest builds both from the same conductors, insulation and noise-dissipation system. The only difference is the connector at one end. Male-to-Male runs from a source straight to an amplifier or receiver. Male-to-Female extends a 3.5mm cable you already own.

Does direction matter when I connect this cable?

AudioQuest says all internal conductors are Direction-Controlled to reduce RF noise. Where the cable carries a direction marking, connect it running from source toward amplifier.

Is Angel balanced or unbalanced?

Unbalanced. This is a single-ended 3.5mm connection, like a typical headphone cable, not a balanced connection.

What warranty does AudioQuest give?

A limited lifetime warranty for the original owner, when you buy from an authorized US dealer like us.

Is there a step up?

Not in the AudioQuest 3.5mm mini range we carry. Angel is the top of that range.

Need a Different Length or Connector?

The most popular configurations are shown on this page. If your system requires a different length or termination, call our audio experts. We’ll help you choose the right configuration and arrange a custom cable for your system.

Why Audio Advisor?

• 40+ Years of Expertise — Since 1981, we've helped over a million music lovers find the right gear.
• 60-Day Money-Back Guarantee — Take your time. Listen, enjoy, and make sure it's right for you.
• Real Experts, Real Help — Our team is here to answer your questions at 800-942-0220, weekdays 9am–6pm EST.
• Free Shipping — On orders over $49, delivered to your door.
• Flexible Payment Options — Financing available so you can start listening now.

Learn More

Want to learn more about interconnect cables, system setup, or matching your gear? Visit our Learning Center for guides, tips, and expert advice.