USED - REFURBISHED - Parasound Halo JC5 Stereo Amplifier

A Chip Off the Old Monoblock

Parasound's Halo JC 5 distills the essence of two Halo JC 1 monoblocks into a single-chassis stereo amp with outstanding sound quality, power, and value.

The JC 5 is a 400-watt per channel stereo amplifier designed by John Curl that combines design elements of two top-of-the-line Halo JC 1 monoblock power amplifiers into a single chassis the same size as one JC 1. The JC 5 combines high power and ultra-high bias Class A/AB sonic quality at roughly two-thirds the price of a pair of JC 1s.

An Enviable Heritage

The Halo JC 5 boasts an enviable heritage. The Parasound Halo JC 1 monoblock was designed by John Curl and introduced 16 years ago to instant international acclaim. It is acknowledged as the benchmark for amplifier performance and value. In 2003, Stereophile awarded it 'Amplifier of the Year' and has honored it as a ‘Class A Recommended Component’ twice a year for fifteen years - far longer than any other audio component.

"Hits a New Sweet Spot"

"The JC 5 is a remarkable amplifier that creates a new sweet spot in our Halo product family," said Parasound's founder and president Richard Schram. "Our customers often tell us they love everything the JC 1 offers, but they wondered if we could deliver comparable performance in a no-compromise stereo amplifier, while saving them money and space. We challenged John Curl to distill the essence of two JC 1 mono blocks into a single chassis, and the result has exceeded everyone's expectations."

Profoundly Powerful, Supremely Musical

The Parasound Halo JC 5 stereo amplifier is profoundly powerful and supremely musical. High bias class A/AB provides 12-watts-per-channel pure class A power and class AB effortlessly to its 400 watts per channel 8 ohm rating. The output stage employs 24 beta-matched, 15 ampere, 60 MHz bipolar transistors to deliver a formidable peak current of 90 amperes.

The power supply employs a 1.7 kVA shielded toroid power transformer with a premium H18 grade steel core. It has independent secondary windings for its dual-mono power supply. As with the JC 1, the input stage B+/B- rails are 10 V above the output stage rails to eliminate any chance of distortion caused by voltage sagging when the amp is under load. Independent power supplies for left and right channels input stages employ filter caps totaling 8,880 μF. Driver and output stages employ massive Rubycon filter caps totaling 132,000 µF.

Direct-Coupled Design

The Halo JC 5 is direct-coupled, protected by DC servo circuits to eliminate coupling capacitors, while extending bass response down to 5 Hz. Its balanced inputs use discrete circuits with Neutrik locking XLR connectors, and Vampire 24k gold-plated RCA input and loop output jacks. “Propeller” type 5-way speaker binding posts are 24k gold-plated and accept 7-gauge bare wire. They are custom-manufactured by CHK Infinium to Parasound’s exacting specifications.

The JC 5 is available in silver or black. Rack mount hardware for its four rack space chassis is included. Shipping weight is 95 lbs.

Product Features

400 watts x 2 @ 8 Ω RMS, both channels driven
600 watts x 2 @ 4 Ω RMS, both channels driven
1200 watts x 1@ 8 Ω, in bridged mode
Circuitry designed by legendary John Curl
Ultra-high bias Class A/AB operation
12 watts per channel of pure Class A power
90 amperes peak current per channel
Stable with speaker impedance dips to 1.5 Ω
Balanced inputs with discrete circuits
CHK Infinium, custom 5-way speaker binding posts
Neutrik locking XLR input connectors
Vampire gold-plated RCA input & loop output jacks
Direct-coupled signal path, no capacitors or inductors
DC Servo and relay protection circuits
AC turn-on inrush surge protection with relay bypass
Dual-mono input stages with ±110 volt DC rails
JFET input stage, MOSFET driver stage
24 beta-matched 15 ampere, 60 MHz bipolar output transistors
1.7 kVA shielded toroid power transformer with independent windings for each channel
Independent power supplies for left & right channel input stages, driver stages, output stages
8,880 µF Nichicon Gold Tune filter capacitors for input stages
132,000 µF Rubycon filter capacitors for output stages
Full power is rated all the way down to 5Hz for unrestricted low-end bass
Harris hyper-fast soft-recovery bridge diode rectifiers
Automatic turn-on by 12 V trigger or audio sensing
4 rack space chassis with rear carry handles
Rack mount hardware is included
Premium quality 9' (3m) 12-gauge IEC power cord, with silver soldered connectors
Available in silver or black

Product Specs

Power Output – Both Channels Driven: 400 watts x 2, 8 Ω; 600 watts x 2, 4 Ω
Power Output – Bridged Mode 1200 watts x 1, 8 Ω; Bridged 4 Ω operation is not recommended
Power measurement parameters are at 120
VAC: 0.05% THD, RMS continuous power, full audio band (20 Hz - 20 kHz)
Current Capacity: 90 amps peak, per channel
Slew Rate: > 130 volts per microsecond
Frequency Response: 5 Hz - 100 kHz, +0/-3 dB; 20 Hz - 20 kHz, +0/-0.25 dB
Total Harmonic Distortion (THD): < 0.05 % at full power; < 0.03 % at typical listening levels
IM Distortion: < 0.04 %
TIM: Unmeasurable
Inter-channel Crosstalk: > 87 dB at 1 kHz; > 72 dB at 20 kHz
Input Impedance: Unbalanced: 33 kΩ; Balanced: 66 kΩ,(33 kΩ per leg)
Total Gain: 29 dB
Input Sensitivity for 28.28 V Output into 8 Ω: Unbalanced 1 V ; Balanced 1 V per leg
S/N Ratio: > 116 dB, input shorted, IHF A-weighted; > 111 dB, input shorted, unweighted
Damping Factor: > 1200 at 20 k Hz
DC Trigger Requirements : +9 Vdc to +12 Vdc, 5 mA
Audio Trigger Requirements: 2 mV - 10 mV
XLR Pin Identification: 1 = Ground (Shield), 2 = Positive, 3 = Negative (Return)
Power Requirement: Standby, 1 Watt; Idle (no music playing), 225 Watts: Typical listening levels, 400 Watts; Maximum 1500 Watts
Dimensions: Width 17-5⁄8", Height without feet 7-1⁄8", Height with feet 7-3/4", Depth: 20", Depth with cables: 21-1⁄2"
Net Weight: 73 lb.

Audio Advisor occasionally has fantastic deals on clearance items that are in excellent condition and we happen to have just one or two of.

Demo: Photo samples, gear we auditioned, items returned for wrong color/wrong size, etc.

Open Box: Contents briefly examined or inspected for promotional or internal purposes

Factory Refreshed: Original-condition items repackaged by the manufacturer

Cosmetically Blemished: A few dings or scratches, but functionally in original condition

Used: May show some signs of use

All clearance products are carefully inspected by our technicians before we offer the item for sale. All clearance products except Used items come with the original manufacturer warranty and are guaranteed to work and sound like new.

RETURN POLICY & PROCESS

NOTE:
You may only return a product purchased within 60-days of the receipt date.
The product must be in like-new condition and shipped in the original packaging (So SAVE THOSE BOXES!!!)

Call 1-800-942-0220 to request an RMA number.
Print the RMA number on the return shipping label.
Please make sure the return shipping name and address are written in a note on the inside.
Ship package to…

Audio Advisor Returns
4717 Broadmoor Ave SE, Suite G
Grand Rapids, MI 49512
(PRINT YOUR RMA NUMBER HERE)

NOTE: If a coupon was used in the ordering process, then the final value (recorded during payment) will be the price refunded.

Returned products are inspected by our warehouse and refunds are issued within 24 hours of inspection. Please note: it may take 7-10 business days for your bank to show the refunded amount. If you do not see it then, please reach out to our customer service team at 1-800-942-0220.

Audio Advisor will ship products anywhere in the United States, including Alaska, Hawaii, and U.S. Territories.